Design and manufacture a lamp in 7 steps

How designer Kyle Wilkinson created a stunning lamp from scratch in just one month.

Earlier this year, multi-disciplinary designer, illustrator and art director Kyle Wilkinson fancied a challenge - so he set himself the challenge of designing and manufacturing a lamp, made from 30 pieces of laser-cut aluminum, within the month of February. Here Wilksinson recalls the process…

Kyle Wilkinson: Prior to this project I'd created two chairs: Latarus, an outdoor rocking chair made out of Cor-Ten weathering steel, and Phaeton, which was made from Perspex.

This was an area I'd previously had absolutely no experience in, and it was the same with the lamp - but I like a challenge.

This project started because I hated the lamp in my bedroom. I wondered if I could make one and set myself the challenge of completing the project within one month.

The results of Wilkinson vs lamp

I knew it was going to be a decorative piece rather than a functional anglepoise lamp. I'm a big fan of Gaudi's architecture and the design was partly inspired by the hyperbolic shapes in some of his work. The aesthetics and practicalities came in while deciding on the material.

Having set myself the challenge of doing it all within February, I didn't actually get started on the first day of the month – I began on the sixth.

On top of that, I picked the shortest month of the year, which also turned out to be the busiest month we'd had in quite some time. Here's how I did it...

01. Planning the process

Laser-cutting was familiar and I knew I wanted to use it for this project, so I had to consider manufacturing lead times

The chairs I made were both laser-cut. Having previously worked with that process, I wanted to use it again – that was the only initial decision I made.

Size and price were considerations, but the manufacturing process was the biggest constraint. The design had to be tied up fairly early in the month.

02. Initial shapes

I grabbed a pen and paper and started sketching some ideas to get an idea of the silhouette

To start with I sketched out some ideas for shapes, thinking about the overall silhouette. Then I moved to the computer to refine the shapes.

I used Illustrator throughout the project, as you can easily edit and play around with form by adjusting different anchor points instead of having to redraw and retrace shapes.

03. Paper and scissors

I took the shapes into Illustrator, printed them to get an idea of scale and used scissors to adjust and refine them

We printed out the shapes to get an idea of the scale and ensure it wouldn't take over the room or blind you. Then we adjusted and refined the design using paper, card and scissors.

With such a tight timeframe to get the design finalised, it was really helpful to be able to move things around quickly.

04. Mass effects

Everything had to slot together correctly. I enjoyed the challenge of figuring this out

The lamp slots together – it doesn't use screws or fittings. Slot width was determined by the depth of the material – we opted for 4mm so it wouldn't be too weak or heavy.

The slots are equidistant from each other, so we had to calculate how many degrees apart to place them, to make sure the pieces slotted together.

05. Working sample

Once the cutting guides were complete, the manufacturer created an MDF prototype

Once the design was finalised, I spoke to the manufacturer and we had a prototype made from MDF to check everything slotted together. The sample was weaker and less rigid, but it indicated scale and size.

We couldn't get multiple prototypes within the timeframe. I used it to read a paper by lamplight – very exciting!

06. Final decisions

After seeing the prototype I made the final decision to use aluminium for the finished lamp

After seeing the MDF sample. Having started the project a week earlier, I'd finished the design – now to make the final version. I struggled to imagine it as a real product. You may think something will look good, but you can never be sure until you actually see it for real.

07. Slot machine

The finished product has 30 separate pieces. Pairing them up was like a game of matching pairs

The final design consists of 30 individually laser-cut pieces. Putting them all together was quite time-consuming.

I hope to manufacture and sell these in different sizes and materials, so I might take some samples to a focus group to decide whether it should be flat-packed or supplied partly or fully built.

Kyle Wilkinson
Kyle is co-owner and creative director of design and digital agency DMSQD, working for clients including Bosch, The Art Directors Club and Computer Arts, as well as experimenting with product design.

The full version of this article first appeared inside issue 239 of Computer Arts, the world's best-selling creative design magazine. Get up to 55 per cent off a subscription to CA here.

Liked this? Try these...